DBCO-PEG4-PFP ester bears a DBCO group and a PFP ester group. While DBCO readily reacts with azides through a copper-free Click Chemistry reaction, the PFP ester can easily react with amine groups. PFP esters are relatively stable and less susceptible to hydrolysis. The hydrophilic PEG linker increase the water solubility of the resulting biomolecules.
Axispharm offers 3000+ PEG Linkers with high purity. Different kinds of PEG Reagents may be available by custom synthesis.
Section I. Identification of the substance
Product Name: DBCO-PEG4-PFP ester
Catalog Number: AP11119
Supplier: AxisPharm, 9823 Pacific Heights Blvd, Suite F, San Diego, CA 92121
Tel: 1-858-677-9432, Email: firstname.lastname@example.org
Section II. Hazards identification
Classification – Not classified as a hazard
Section III. Composition and information on ingredients.
Name: DBCO-PEG4-PFP ester
Formula Weight: 718.67
Section IV. First aid measures
Skin contact: Immediately wash skin with copious amounts of water for at least 15
minutes while removing contaminated clothing and shoes. If irritation persists, seek
2. Eye contact: Immediately wash skin with copious amounts of water for at least 15
minutes. Assure adequate flushing of the eyes by separating the eyelids with fingers. If
irritation persists, seek medical attention.
Inhalation: Remove to fresh air. In severe cases or if symptoms persist, seek
Seek medical attention.
Section V. Firefighting measures
In the event of a fire involving this material, alone or in combination with other materials,
use dry powder or carbon dioxide extinguishers. Protective clothing and self-contained
breathing apparatus should be worn.
Section VI. Accidental release measures
Personal precautions: Wear suitable personal protective equipment which performs
and meets local/state/national standards.
Respiratory precaution: Wear approved
mask/respirator Hand precaution: Wear suitable
Skin protection: Wear suitable protective
clothing Eye protection: Wear suitable eye
Methods for cleaning up: Mix with sand or similar inert absorbent material, sweep up and
keep in a tightly closed container for disposal. See section 12.
Environmental precautions: Do not allow material to enter drains or water courses.
Section VII. Handling and storage
Handling: This product should be handled only by, or under the close supervision of, those
properly qualified in the handling and use of potentially hazardous chemicals, who should
take into account the fire, health and chemical hazard data given on this sheet.
Storage: Store in closed vessels, refrigerated.
Section VIII. Exposure Controls / PPE
Engineering Controls: Use only in a chemical fume hood.
Personal protective equipment: Wear chemical-resistant gloves, safety goggles.
General hygiene measures: Wash thoroughly after handling. Wash contaminated clothing
Section IX. Physical and chemical properties
Odor: No data
Boiling Point: No data
Melting Point: No data
Flash Point: No data
Density: No data
Chemical Formula: C36H35F5N2O8
Section X. Stability and reactivity
Conditions to avoid: Heat, flames and sparks.
Materials to avoid: Oxidizing agents.
Possible hazardous combustion products: No data available.
Section XI. Toxicological information
Section XII. Ecological information
Section XIII. Disposal consideration
Arrange disposal as special waste, by licensed disposal company, in consultation with local
waste disposal authority, in accordance with national and regional regulations.
Section XIV. Transportation information
Non-hazardous for air and ground transportation.
Section XV. Regulatory information
Indication of Danger: No data.
Risk Statement: No data.
Safety Statement: In case of contact with eyes, rinse immediately with plenty of water and
seek medical advice. Wear suitable gloves and eye/face protection.
Section XVI. Other information
This SDS is correct to the best of our knowledge and belief at the date of its publication but
does not purport to be all inclusive and shall be used only as a guide. AxisPharm shall not
be held liable for any loss, injury or damage which may result from its use. This product is
for research and development use only.